Chat on WhatsApp | MON–FRI 8:00 AM – 6:00 PM EST
Hybrid & EV Battery Specialists
EnerCellix.EV / FAQ / Technical FAQ

Hybrid battery technical FAQ

The questions workshops and battery specialists actually ask — answered with the numbers from our module specifications and assembly procedures, not general advice. Voltage per platform, internal resistance, torque values, probe positions, shipping state of charge, storage intervals.

47 questions Ni-MH hybrid battery packs Cylindrical and prismatic modules Updated November 2026

Fitment and selection

How do I know which pack fits my car?
Send the 17-character VIN — it is more reliable than the model year. The same nameplate can change module count, voltage and connectors between facelifts. We confirm three things in writing before dispatch: pack shape, number of modules and total voltage. If the fitment error is ours, we take the pack back at our cost.
Why is one Camry 244.8 V and another 288 V?
Because they are not the same pack. Camry XV40/XV50 hybrid use 17 modules of 14.4 V, which gives 244.8 V. RX400h, RX450h and Highlander use 15 modules of 19.2 V, which gives 288 V. Different voltage means the modules cannot be mixed, and the connectors and brackets differ too — always match by vehicle, not by voltage alone.
What is the difference between your cylindrical and your block modules?
Two different module families. Cylindrical (orange cells): 25C continuous discharge, −30 to +55 °C, design life over 3000 cycles, about 1.02 kg per 7.2 V module. Block (prismatic, plastic case): 65C continuous discharge, −40 to +60 °C discharge and −20 to +50 °C charge, design life over 6000 cycles, about 1.25 kg per 7.2 V module. Both are brand new Ni-MH at 6.5 Ah nominal and both fit the original tray.
Can cylindrical cells really replace the original prismatic modules?
Yes. Nominal voltage is the same 7.2 V per module. Power density is practically identical (1022 vs 1023 W/kg at SOC 60%, 25 °C, 10 s), and both are rated beyond 300,000 km. The cylindrical module is actually denser by volume — 125 Wh/L against 79 Wh/L — so it fits the original tray with shorter thermal paths. The real difference is capacity: 6.0 Ah against 6.5 Ah, and that is covered in the next answer.
Capacity is 6.0 Ah instead of 6.5 Ah — is that enough?
Hybrid packs are power cells, not energy cells. The vehicle only works the pack between roughly 20 % and 80 % state of charge and relies on burst current, not total ampere-hours. Our cylindrical module is rated 25C continuous discharge, the block module 65C, both far above what the vehicle asks for. A 0.5 Ah difference is not visible in real driving; internal resistance and power at temperature are what the car actually feels, and there we match the original.
Why do some cars need 14 modules, others 17 or 20?
Module count follows total voltage, and total voltage is set by the platform. 14 × 14.4 V = 201.6 V (Prius 2nd and 3rd gen, CT200h). 17 × 14.4 V = 244.8 V (Camry, ES300h, NX300h). 20 × 14.4 V = 288 V (GS450h). 15 × 19.2 V = 288 V (RX400h, RX450h, Highlander). Work out the voltage first, then count modules.
Do I have to replace the whole pack, or only the modules inside?
Our replacement scheme changes the modules and part of the internal wiring only. The original battery case, cover plates and mounting points stay. Weight distribution and crash structure are unchanged, and the pack looks identical from outside. Replacing the entire case is a different approach — higher cost and much larger shipping volume.
My car is a parallel or used import — the local catalogue does not list my configuration.
That is common: Japanese used hybrids are exported to Southeast Asia, Russia and the Middle East in large numbers, and their configuration often differs from the local official version. We do not rely on local catalogues. Send the VIN plus three photos: the pack nameplate, the module arrangement, and the connector positions. That is normally enough to identify the right set.
Will a pack from a different model year fit?
Not necessarily. On Prius, the 1st generation uses 20 single L6 cylindrical modules, while the 2nd and 3rd generations use 14 double modules at 201.6 V. Voltage may look similar, but module shape, brackets and connectors are completely different. A close model year is not a guarantee — check by VIN.
Both RX generations are 288 V — can the packs be swapped?
No, not directly. RX400h and RX450h are both 288 V, but module format, brackets and connectors differ, which is why we list them as two separate items (53.5 kg and 53.1 kg packs). Same voltage only means the same number of cells in series — it says nothing about how the pack physically mounts.
Are Honda Insight, Civic and CR-Z packs interchangeable with Toyota?
No. Honda uses L6 double modules (14.4 V per set); Toyota uses L6 single modules (7.2 V) or S12 modules (14.4 V). The voltage may coincide but the module size, busbars and connectors do not. Note also that Civic switched from Ni-MH to lithium from 2011 and dropped the Ni-MH version around 2013–2014, so confirm which version you have.

Performance and service life

How long does a new pack last?
It depends on the module family. Cylindrical: design life over 3000 cycles at 80 % depth of discharge, rated beyond 300,000 km. Block: over 6000 cycles at the same depth, with a higher continuous discharge rating. Real life depends on climate and duty: constant heat and repeated deep cycles shorten either one. We warrant 3 years or 100,000 km, whichever comes first, and the warranty follows the serial number, not the owner.
What does the cycle life figure actually mean?
The test runs 80 % depth of discharge — charged to 90 %, discharged to 10 % — with the module held at 35 °C and cycled on a profile that imitates real driving rather than a constant current bench test. That is a harsher and more realistic condition than a simple 1C lab cycle, which is why we present the number as design life rather than a guarantee.
Can it be used at −30 °C? Is it suitable for Russia or Canada?
Yes. Cylindrical modules run −30 to +55 °C. Block modules run −40 to +60 °C on discharge and −20 to +50 °C on charge, which is why they are the usual choice for Russia, Canada and the Nordics. Power drops in extreme cold and the vehicle limits output to protect the pack, so nothing breaks. Storage stays −20 to +35 °C for either family, and long storage without a top-up charge is what actually damages them.
Thailand and the Middle East are very hot — will the pack fail early?
We validated heat behaviour: three days at 55 °C followed by seven days at 20 °C, with self-discharge staying below 18 % and no abnormality. In the car the pack has its own air duct and temperature probes on modules 1, 7 and 14, and the controller limits current when it gets hot. The real risk is a car parked in direct sun for weeks — advise customers to avoid that.
Does the pack self-discharge? How long can it sit?
Yes, slowly. Measured self-discharge is under 18 % after three days at 55 °C plus seven days at 20 °C. At room temperature a stored pack loses a few percent a month. The point that matters is the three-month rule: a pack in stock beyond three months needs a top-up charge, otherwise it can over-discharge and lose capacity permanently.
What is the internal resistance, and why does it matter?
Cylindrical 7.2 V module: DC internal resistance ≤16 mΩ at 50 % state of charge, AC impedance ≤6.9 mΩ at 1 kHz. Block 7.2 V lithium module: AC impedance under 3 mΩ. Block Ni-MH sits between the two. Resistance decides voltage sag and heat under load. An aged pack often still shows capacity but has doubled resistance — that is exactly why a car can read "full" and still feel gutless or throw a hybrid fault. Low resistance is the real proof a pack is healthy.
What does 85 % energy efficiency mean?
Put 100 units of energy in and 85 come back out; the rest becomes heat and loss. In a hybrid that number feeds straight into fuel consumption, because a less efficient pack makes the engine work more to compensate. Our modules are rated ≥85 % energy efficiency and >95 % capacity efficiency, which is why fuel consumption usually improves slightly after replacement.
Will fuel consumption improve after replacing the pack?
Slightly. One Prius we monitored covered 7500 km after replacement with zero faults and went from 5.7 L to 5.2 L per 100 km. The reason is lower internal resistance and better charge acceptance, so the engine cuts in less often. It is not a dramatic saving, but it is a clear sign the pack is working as intended. Single vehicle measurement — not a blanket promise.

Safety and shipping

Which safety tests have the modules passed?
Mandatory module-level tests include over-discharge, over-charge, heating (ramped 5 °C per minute to 85 °C, held two hours), crush (75 mm radius半cylindrical platen, 5 mm/s, up to 200 kN), nail penetration and vibration (10–55 Hz, 30 m/s², three hours). Acceptance criteria are no fire, no explosion, no deformation, no leakage. These are module tests; the vehicle BMS provides the system-level protection.
What documents are needed for shipping, and can you deliver to my country?
Ni-MH packs are dangerous goods. Sea freight requires a UN38.3 test summary, MSDS, dangerous-goods packing certificate, commercial invoice and packing list. We prepare the full set for every shipment and book through forwarders licensed for class 9. Air freight can be arranged on request, but the per-unit cost is much higher; sea is the standard route at 25–40 days.
Can the pack leak or catch fire?
Ni-MH is fundamentally safer than lithium: the electrolyte is aqueous and there is no thermal runaway chain. Under normal use it will not leak. Leakage only happens in three situations — prolonged over-discharge (sitting more than six months without a charge), a punctured or crushed case, and charging with the wrong charger. All three are explicitly prohibited in our documentation.
Does the car need programming or coding after fitting?
No. In the vehicle architecture the pack is a managed component: the original controller reads its data and re-learns after replacement. Fit the pack, clear the stored codes, drive a few tens of kilometres and the system settles. There is no software to flash and no proprietary diagnostic session required — a point worth telling workshops, because many assume otherwise.
The pack is high voltage — is installation dangerous?
It carries risk and must follow procedure. Pack voltage exceeds 96 V, so isolate the vehicle MSD (service disconnect) before work, keep every harness terminal insulated throughout, connect negative first and positive last, and install the original fuse only at the very end. Busbar screws are torqued to 5–6 N·m. Installation should only be done by trained technicians.

Installation detail

How heavy is one module, and what are the dimensions?
Cylindrical 7.2 V: about 1.02 kg, 33 mm diameter × 397 mm long. Block 7.2 V: about 1.25 kg, 282 × 21.5 × 117 mm. Block 9.6 V: about 1.56 kg, 380 × 15.5 × 95.5 mm. Block 14.4 V: about 2.33 kg, 559 × 15.5 × 95.5 mm. A full 201.6 V pack of 28 block modules lands around 33 kg, a 288 V pack of 30 modules around 53 kg.
Why does a 244.8 V pack mix 12 modules of one size and 9 of another?
Because the original pack is built that way. 12 × 9.6 V plus 9 × 14.4 V gives 244.8 V, which is what Alphard 20, Estima and Previa use. 201.6 V is 28 × 7.2 V (Prius 3, CT200h, Corolla). 288 V is either 30 × 9.6 V (RX400h, RX450h) or 20 × 14.4 V (GS450h, LS600h). The mix is not a compromise — it mirrors the factory layout so the tray and busbars are reused.
What insulation test must be completed before the pack goes into the car?
A 500 V insulation resistance test: one probe on the pack main positive or negative, the other on the pack case or vehicle ground. The reading must be above 100 MΩ before installation. Below 100 MΩ the pack must not be fitted — it means something in the assembly is touching the case or the harness is damaged. Record the value; it is the single number that decides whether the car throws an insulation fault.
What causes insulation faults after installation?
Moisture, nine times out of ten. A damp battery compartment, standing water, condensation from a temperature swing, or a broken boot seal all drag the insulation value down. Never fit a pack into a compartment with visible condensation, and dry the compartment, harness connectors and mounting points with warm air first. Check the hatch seals and the boot floor for leaks — a pack that faults again three weeks later is usually a wet compartment, not a bad module.
What should be checked on reused busbars, harness and controller?
Reused parts cause a surprising share of repeat failures. Check that the busbars and connecting plates are the correct model, free of corrosion and not deformed; that the connectors are not cracked or pushed back; that the controller is the matching part number; and that the pack vent is clear. If a plate is corroded, replace it — cleaning it only moves the resistance problem to the next joint.
Do I need to clear stored fault codes after fitting?
Yes, and before you hand the car back. Power up, confirm the pack reads correctly, then clear the codes stored from the old pack, and only then refit the covers and the service plug. Codes left over from the previous pack will keep the car in limp mode and make the new pack look faulty. Take a code reading before and after so there is a record that the fault did not return.
Do I need to buy a new harness or connecting plates with the pack?
No. The voltage-sensing harness, connecting plates and temperature sensors are original vehicle parts and are reused. What you get is the modules plus the installation manual — there is nothing extra to source. Worth telling a customer plainly, because anyone who expects to hunt for a harness assumes the job is harder than it is. Check the reused plates for corrosion before fitting and replace any that are pitted. If the manual is unclear, the installation video and our support cover the sequence step by step.
What torque should the busbar screws be tightened to?
5–6 N·m, checked with a torque wrench rather than by feel, and never above 6 N·m — that is the ceiling in the assembly procedure. Too much torque cracks the module terminal, which is not repairable. Too little leaves high contact resistance, which heats up and can burn the joint. After assembly, re-check a sample of joints before closing the pack — this single number prevents most installation failures we see.
Where do the temperature probes go?
On a 14-module pack the probes sit on the bottom clips of modules 1, 7 and 14, with the probe harness clips on modules 4 and 10. Wrong positions distort the controller temperature reading: false overheat warnings in summer and refusal to charge in winter. The safest method is to note the positions while dismantling the original pack and refit in the same order.
Do modules have an orientation?
Yes — positive and negative must face the direction shown in the manual. Fit module 1 first and fix its base as the datum, then follow the serial numbers marked on the modules. Also wrap the four fixing supports with insulating tape so the modules are isolated from the brackets. Reversed polarity ranges from "does not work" to a dead short.
How do I verify the installation is correct?
Three checks. First, read pack voltage with a scan tool — it should sit in the 196–250 V band on this class of pack. Second, road test and watch current: a peak around 80 A with an average near 12 A is normal city behaviour. Third, drive 20–50 km and re-read codes; no P0A80 or P0AFA means the pack is accepted.
What should be avoided after fitting a new pack?
Keep the first 500 km gentle so the controller completes learning. Make sure the cooling duct under the rear seat is not blocked — a common cause of premature failure. Avoid parking in direct sun for long periods in hot climates. And never mix new modules with old ones: the old ones drag the new pack down within months.
Can an end customer install it themselves?
Not advisable. Even with the manual, the work involves high voltage, insulation discipline, torque control and harness routing; a mistake can destroy the controller or start a fire. Our product is aimed at workshops and battery specialists. With a torque wrench, insulated gloves and a scan tool, they complete one vehicle in two to three hours.

Stock and maintenance

What state of charge does a pack ship in?
At partial charge, never full and never empty: block modules ship at about 40 % state of charge, cylindrical modules between 30 % and 90 % depending on transit distance and packaging. Full charge is a transport risk; empty risks over-discharge in storage. This matters commercially: a customer who tests capacity straight out of the box will read low. Discharge first, then measure, or you will see a false "capacity shortfall".
How long can stock sit, and when does it need a top-up charge?
Top up every three months. Sea transit can take about 60 days, so the first top-up should happen within 90 days of receipt, before the pack is assembled and sent to the end customer. Beyond three months without attention the pack over-discharges, and that leads to leakage, refusal to charge and capacity that cannot be recovered.
What is the top-up charge procedure for stock modules?
Five steps, 25 ± 5 °C, ventilated. One: constant current 6 A for 18 minutes (about 30 % state of charge), stop at 18.0 V or 42 °C. Two: rest 5 minutes. Three: constant current 1.2 A for 30 minutes (about 10 %), same stop conditions. Four: rest 30 minutes. Five: discharge 6 A for 5 minutes (about 8 %), stop at 15.0 V. Run it on every batch before shipping and every three months in stock.
What are the long-term storage requirements?
Store between −20 °C and +35 °C, dry and ventilated, out of direct sunlight, in a dedicated area away from flammable or explosive goods. If a pack is stored while connected to a charger or device, keep the quiescent current below 5 µA so the pack cannot slowly drain into over-discharge. Never stack heavy items on the modules.
Can new and old modules be mixed?
Never. Modules of different capacity, model, brand or state of charge must not share a pack. The new module gets dragged down by the aged ones within months, and during charging the imbalance means the old modules overcharge first. Replace the set, not the weakest piece. This single rule prevents most repeat failures we see in the field.
How much attention does a pack need once installed?
Almost none — the vehicle controller manages it. Human intervention is needed only in stock, where the three-month top-up applies. Beyond that, inspect the pack cooling duct and filter roughly every two years; dust build-up reduces airflow, raises cell temperature and shortens life. That is genuinely all the routine maintenance a Ni-MH traction pack needs.

Buying and service

How does the warranty work, and does it survive a change of owner?
3 years or 100,000 km, whichever comes first, exactly as published on the site. The warranty follows the pack serial number, so it stays valid if the car is sold. Coverage applies to abnormal capacity loss, abnormal resistance rise, leakage and open circuit. It does not cover water damage, collision damage or damage from an incorrect charger.
What happens if the pack fails?
A pack almost never fails as a whole. In practice one module fails, and we replace that module only — not the full pack. Return freight for the failed module is on the customer. Diagnosis first: read the fault codes, measure total voltage and module-to-module spread; we can usually tell from those numbers whether it is one module or a wiring issue.
What is the minimum order quantity?
One pack for retail, and five packs for wholesale pricing, mixed models allowed. Above ten packs we can discuss payment terms. We do not run a low headline price and add surcharges later — the quote you receive is the landed price for the quantity quoted.
Can you produce under our own brand?
Yes. Private label from 50 packs per model: your label, packaging, manual and warranty card. We can also specify the cell chemistry for a given model — for example a sodium-ion variant instead of Ni-MH — subject to minimum quantity and validation time. Certification documents stay with the pack; branding is yours.

Not answered here?

Send the VIN and the fault code. We answer with the pack, the price and the shipping window for your country.